Alpha-technologies Cordex Controller Ver.3.1x Manuel d'utilisateur Page 73
- Page / 144
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
71
0700015-J0 Rev B
6.7.1. 2 Calibration of Analog Input Channels
Calibrate the selected channel by setting the high point or low point or both as shown in the following
example. For static calibration, refer to the next section.
A more detailed procedure can be found on the Alpha website (www.alpha.ca) under
Technical Documentation > Misc Documents > Method of Procedure.
Static Calibration
Static calibration enables the Supervisor to calibrate controller analog inputs without the need for a live
signal at the input. This is especially useful for calibrating current inputs for systems in the field. See the
following figures.
Figure 72 — Analog Inputs calibration example (Signals > Calibrate Analog Inputs)
Tap Save or Restore
Default as required
Discard changes and return to
previous screen
Sliders and scroll bars are used for
navigation
Select menu item to congure
Accept changes and return to
previous screen
Figure 73 — Static calibration – LCD interface
Exit by tapping Cancel
- Your Power Solutions Partner 1
- User Manual 1
- Version 3.1x 3
- Contents 4
- List of Tables 7
- 1. Introduction 8
- 2. Standard Features 9
- 2.4 Mixed Rectifier System 10
- 2.5 Safe Voltage 10
- 2.6 Power Save 10
- 2.7 Auto DC Priority 10
- 2.11 Battery Test Scheduler 12
- 2.13 Signals Management 12
- 2.14.1 Analog Statistics 13
- 2.14. 2 Battery Log 13
- 2.14.3 Data Logging 14
- 2.14.4 Event Log 14
- 3. User Interface Options 15
- 3.4 Menu Navigation - LCD 17
- 3.4.3 Logging Out 18
- 3.4.4 Virtual Numeric Keypad 18
- 3.4.5 LCD Menu Structure 18
- Count down 20
- 4.2 Language Selection 21
- 4.1 Start-up 21
- 4.3 Date and Time 22
- 4.5.1 Silence All Alarms 23
- 4.6 Signals Display 24
- 4.7.1 Inventory Update 26
- To change modes: 27
- 4.9 Float (FL) Mode 28
- 4.10 Equalize (EQ) Mode 28
- 4.11 Boost (BST) Mode 28
- 4.12.3 BT Initiation 29
- 4.13 Communications 30
- 5.1 Communication Settings 31
- 5.2 Getting Started 32
- 5.3 Login 33
- 5.4 Language Selection 33
- 5.5 Saving Changes 33
- 5.6 Date & Time 34
- 5.8 Converters 35
- 5.9 Rectifiers 35
- 5.10 Inverters 35
- Figure 30 — CXCU controller 36
- Controller > 36
- 6.1 System Info 38
- 6.1.3 Set ADIO Module Number 39
- 6.1.4 Site Information 39
- 6.1.5 Temperature Units 40
- 6.1.6 Factory Information 40
- 6.2 Converters 41
- 6.3 Rectifiers 41
- 6.4 Inverters 45
- 6.4.4 General Settings 48
- 6.4.5 Set Inputs 49
- 6.4.7 Auto DC Priority 50
- 6.5 Batteries 52
- 6.5.3 Battery Monitor 53
- 6.5.5 Boost (BST) Mode 55
- 6.5.7 Battery Properties 56
- 6.5.8 Battery Information 57
- 6.5.9 Battery Test Scheduler 57
- Enable Periodic BT 58
- Enable Scheduled BT 58
- 6.6 Alarms 59
- 6.6.3 Configuring Alarms 60
- 6.6.4.1 Rectifier Alarms 62
- 6.6.4.2 Digital Alarms 63
- 6.6.5.5 Miscellaneous Alarms 65
- 6.6.5.6 ADIO Alarms 66
- 6.6.5.7 Custom Alarms (1-20) 66
- 6.6.5.8 Converter Alarms 68
- 6.6.8 Alarm Tone 71
- 6.6.9 Configuring ALCO 71
- 6.7 Signals 72
- 6.7. 2.1 Controller Signals 74
- 6.7. 2 Configure Signals 74
- 6.7.2.2 Analog Inputs 75
- 6.7. 2. 3 Digital Inputs 75
- 6.7. 2.4 Rectifier Signals 75
- 6.7. 2. 5 Custom Signals 75
- (in Amperes/50 mV) 76
- 6.7.2.7 Midnight Rollover 77
- 6.7. 2. 8 Converter Signals 78
- 6.7. 2.9 Inverters 78
- 6.7. 2.10 Timers 79
- 6.7. 2.11 Counters 79
- 6.7. 2.12 ADIO Signals 80
- Figure 92 — Log Frequency 84
- 6.7.3.3 Retrieve Logs 85
- 6.8 Controls 91
- 6.9 Communications 93
- 6.10 Hardware 95
- 6.11.1 Retrieve Logs 96
- 6.12 Supervisor 98
- 7. Advanced Programming 100
- 7.3 Tips on Programming 101
- 8.2 PPP Connection Devices 103
- 8.3 Rear Port Configuration 104
- CAUTION! 105
- 9. Remote Communications 106
- 9.2.3.1 Modem Configuration 109
- 0700015-J0 Rev B 110
- COM port as shown below: 110
- Figure 139 — Modem Status 112
- 9.3 Modem Connection 113
- 9.3.2 Computer Setup 114
- 10.1 Overview 115
- 10.1.3 Typical UDP Transport 116
- Figure 142 — VarBinds 117
- 10.3.2 SNMP Trap Recovery 118
- Submenu Item 127
- Default Setting Units 129
- Alarm Type Cause Solution 132
- PDU Address 139
- Number of 139
- 13. Trouble-shooting 141
- 14. Alpha Conventions 142
- Visit us at www.alpha.ca 144
Produits connexes et manuels pour Logiciel Alpha-technologies Cordex Controller Ver.3.1x
(57 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.017 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels